mo.mix mos2-75
Inneres Gleit- und Schmiermittel – Masterbatch
Internal lubricant and lubricant – masterbatch
Artikelnummer: | 6301 |
Anwendung: | Gleitmittel zur Verbesserung tribologischer Eigenschaften |
Hauptwirkstoff: | Molybdändisulfid (MoS2) |
Träger: | Polyethylen / Ethylen-Acrylat-Copolymer |
Item no.: | 6301 |
Application: | Gleitmittel zur Verbesserung tribologischer Eigenschaften |
Main active ingredient: | Molybdenum disulfide (MoS2) |
Carrier: | Polyethylen / Ethylen-Acrylat-Copolymer |
Konzentration:
75,0 %
Verarbeitungstemperatur:
100 °C – 300 °C
Gleitmittelwirkung:
-100 °C – 200 °C
Lieferform:
Granulat
Concentration:
75,0 %
Processing temperature:
100 °C – 300 °C
Lubricant effect:
-100 °C – 200 °C
Delivery form:
Granulat
ABS, Ethylen-CoPolymer, PA, PC, PET, POM, PP, PPO, PS, PVC, TPE
schwarz
ABS, Ethylen-CoPolymer, PA, PC, PET, POM, PP, PPO, PS, PVC, TPE
schwarz
mo.mix mos2-75
Inneres Gleit- und Schmiermittel – Masterbatch
Eigenschaft | typische Werte |
Wirkstoffgehalt | 75,0 % |
Schmelztemperatur Träger | 95 °C |
Wirkstoffpartikelgröße d50 | 15 µm |
Temperaturbereich der Gleitmittelwirkung | -100 °C – 200 °C |
Verarbeitungstemperatur | 100 °C – 300 °C |
Schüttgewicht | 1200 g/l |
- Bildung eines permanent regenerationsfähigen MoS2- Gleitfilms bei Reibeinwirkung an Teileoberflächen
- verbessert die tribologischen Eigenschaften der Teile durch Reduktion des Reibungskoeffizienten - geringer Energieverbrauch - gute Verschleißfestigkeit - verlängerte Wartungsintervalle
- Wirksamkeit als Gleitmittel in einem extrem weiten Temperaturbereich
- hohe Effektivität in Kunststoffteilen durch hohe Wirkstoffkonzentration
- inneres Gleitmittel in den Kunststoffschmelzen während der Verarbeitung
- reduziert Friktion und Wärmedissipation
- einfache und sichere Dosierbarkeit
- frei von Mineralöl und anderen nicht thermisch hoch beanspruchbaren Komponenten
- mechanisch bewegte / beanspruchte Systeme
- durch Gleitreibung beanspruchte Teileoberflächen zur Reduktion von Reibung und Verschleiß
- verwendbar in allen thermoplastischen Kunststoffen, bevorzugt in technischen Kunststoffen wie Polyamiden, POM, PPO etc.
lange lagerfähig in geschlossenen Gebinden unter 50 °C
In Abhängigkeit von Einsatzgebiet, Kunststoffart, Kraft- und Pressverhältnissen an Teileoberfläche: 1,0 % – 3,0 %
PE-Bag à 25 kg netto, 1.000 kg/Palette
Stand: 002/0324
Unsere technischen Daten stützen sich auf sorgfältige Untersuchungen und stellen unseren aktuellen Erkenntnisstand dar. Dennoch sollen sie nur unverbindlich beraten.
Our technical information is based on careful examinations and is believed to be reliable, but is presented without guarantee.
kcd Kunststoffe, Additive und Beratung GmbH, D-99427 Weimar, Otto-Schott-Str. 5
Tel.: +49 (0) 3643 404837
Fax: +49 (0) 3643 404838
e-mail: info@kcd-additive.com
web: www.kcd-additive.com
mo.mix mos2-75
Internal lubricant and lubricant – masterbatch
Characteristic | Typical values |
Active agent content | 75,0 % |
Melting temperature of carrier | 95 °C |
Active agent particle size d50 | 15 µm |
Temperature range of the lubricant effect | -100 °C – 200 °C |
Processing temperature | 100 °C – 300 °C |
Bulk weight | 1200 g/l |
- Formation of a permanently regenerative MoS2 sliding film when friction occurs on part surfaces
- improves the tribological properties of the parts by reducing the coefficient of friction - low energy consumption - good wear resistance - extended maintenance intervals
- effective as a lubricant in an extremely wide temperature range
- High effectiveness in plastic parts due to high concentration of active ingredients
- internal lubricant in the plastic melts during processing
- reduces friction and heat dissipation
- easy and safe dosing
- free of mineral oil and other components that are not subject to high thermal stress
- mechanically moved/stressed systems
- Part surfaces subjected to sliding friction to reduce friction and wear
- can be used in all thermoplastics, preferably in technical plastics such as polyamides, POM, PPO etc.
Can be stored for a long time in closed containers below 50 °C
Depending on the area of application, type of plastic, force and pressing conditions on the part surface: 1.0 % – 3.0 %
PE bag of 25 kg net, 1,000 kg/pallet
Status: 002/0324
Unsere technischen Daten stützen sich auf sorgfältige Untersuchungen und stellen unseren aktuellen Erkenntnisstand dar. Dennoch sollen sie nur unverbindlich beraten.
Our technical information is based on careful examinations and is believed to be reliable, but is presented without guarantee.
kcd Kunststoffe, Additive und Beratung GmbH, D-99427 Weimar, Otto-Schott-Str. 5
Tel.: +49 (0) 3643 404837
Fax: +49 (0) 3643 404838
e-mail: info@kcd-additive.com
web: www.kcd-additive.com
Verwandte Produkte
Art.-Nr. | Name | Konzentration | Verarbeitungstemp. | Gleitmittelwirkung |
6201 FG | mo.mix ptfe 60 FG | 60,0 % | 100 °C – 300 °C | -100 bis 200 °C |
6303 | mo.mix si20 | 20,0 % | 100 °C – 300 °C | -100 bis 200 °C |
6303 FG | mo.mix si20 FG | 20,0 % | 100 °C – 300 °C | -100 bis 200 °C |
6405 | stearate.mix a01 | 70,0 % | 100 °C – 250 °C | bis 100 °C |
Related products
Item no. | Name | Concentration | Processing temperature | Lubricant effect |
6201 FG | mo.mix ptfe 60 FG | 60,0 % | 100 °C – 300 °C | -100 bis 200 °C |
6303 | mo.mix si20 | 20,0 % | 100 °C – 300 °C | -100 bis 200 °C |
6303 FG | mo.mix si20 FG | 20,0 % | 100 °C – 300 °C | -100 bis 200 °C |
6405 | stearate.mix a01 | 70,0 % | 100 °C – 250 °C | bis 100 °C |